Scania PCS fault codes

Showing 181–240 of 240 codes

• 4096hex 001000 Parasitic losses of ICE erroneous signal
• 4097hex 001001 Friction torque of ICE erroneous signal
• 4098hex 001002 Dynamic Flywheel Torque of Engine out of range
• 4099hex 001003 Too low value of reference engine torque
• 4100hex 001004 Reference Engine Torque erroneous signal
• 4101hex 001005 Reference torque for Engine Exhaust Brake out of range
• 4102hex 001006 Reference Torque for Exhaust Brake erroneous signal
• 4103hex 001007 Current max static flywheel torque of ICE reported out of range
• 4104hex 001008 The value of basic low idle speed from EMS is higher than the PCS low idle setting
• 4105hex 001009 Friction torque for Engine is out of range
• 4106hex 00100A Too high value of reference engine torque
• 4107hex 00100B The value of ActMaxAvailTq (CAN message EEC2) is higher than the value calculated from CAN message EngineConfig curve
• 4108hex 00100C Parasitic torque for Engine is out of range
• 4109hex 00100D The value of the signal Actual Maximum Available Engine Torque (CAN message EEC2), is recieved as NA or ERROR.
• 4110hex 00100E The value of Actual Max Avail Retarder (CAN ERC1) is higher than the value calculated from CAN message RetarderConfig curve.
• 4111hex 00100F The value of Actual Max Avail Retarder (CAN ERC1) is NA or ERROR.
• 4112hex 001010 CAN timeout on message EngineConfig_E from EME1
• 4113hex 001011 CAN timeout on message EEC1_EME1_E from EME1
• 4114hex 001012 CAN timeout on message EEC2_EME1_E from EME1
• 4115hex 001013 CAN timeout on message EEC3_50_E from EME1
• 4116hex 001014 CAN timeout on message DLN2_E from EME1
• 4117hex 001015 CAN message missing
• 4118hex 001016 CAN timeout on message EngConfProp2_E from EME1
• 4160hex 001040 Control switch, invalid signal
• 5001hex 001389 Supply voltage above maximum level
• 5002hex 00138A Supply voltage below minimum level
• 5010hex 001392 Supply voltage below minimum level
• 12289hex 003001 Configuration faults
• 24576hex 006000 The direct current converter does not convert to 24 V
• 24577hex 006001 Direct current converter in fault mode
• 24578hex 006002 CAN message missing
• 24579hex 006003 CAN message missing
• 24580hex 006004 CAN message missing
• 24592hex 006010 Electrical air compressor system, CAN message missing
• 24593hex 006011 Electrical air compressor system, CAN message missing
• 24594hex 006012 Electrical air compressor system, CAN message missing
• 36864hex 009000 Failed attempts to build up accumulator pressure
• 43968hex 00ABC0 CAN message is missing from the battery control unit
• 43969hex 00ABC1 CAN message is missing from the battery control unit
• 43970hex 00ABC2 CAN message is missing from the battery control unit
• 43971hex 00ABC3 CAN message is missing from the battery control unit
• 43972hex 00ABC4 CAN message is missing from the battery control unit
• 43973hex 00ABC5 CAN message is missing from the battery control unit
• 57351hex 00E007 Critical values missing from MGU control unit
• 57353hex 00E009 Inverter, incorrect status
• 57354hex 00E00A Electric machine, fault in torque
• 57355hex 00E00B BMU control unit, critical values missing
• 57356hex 00E00C BMU control unit, wrong status
• 57358hex 00E00E EMU control unit, fault in CAN communication
• 57359hex 00E00F Safety measures for the electric drive system are not working as expected
• 57361hex 00E011 MGU control unit, wrong status
• 57362hex 00E012 BMU control unit, not reaching correct status
• 57376hex 00E020 Battery heater, error message
• 57377hex 00E021 Oil pump, error message
• 57378hex 00E022 Voltage class B, large deviation in electric power consumption
• 57379hex 00E023 Voltage class B, slight deviation in electric power consumption
• 57380hex 00E024 Oil pump, wrong speed
• 57381hex 00E025 MGU control unit, faulty
• 57393hex 00E031 EMU reports bad status on the inverter cooling circuit
• 57394hex 00E032 VCB voltages diverging